Hard Turning, Tool Life, and Surface Quality
Justify hard turning by examining cutting conditions
By Ty G. Dawson, Thomas R. Kurfess, The George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA
Engineers want materials with long service lives, and processes for shaping them into finished products with tight geometric tolerances and excellent surface finish. Hardened steel is one such
material, used particularly in the automotive industry for components such as bearings, gears, shafts, and cams. Soft steel must be hardened to increase the strength and wear resistance of parts
made from this material. Traditionally, finished surfaces must be ground on near-net-shape, hardened-steel parts.
However, the grinding process itself may require several machine tools and several setups to finish all component surfaces. Because grinding can be a slow process with low material-removal rates,
there has been a determined search for replacement processes.
Cutting edge condition of new tool
Enter hard turning. Recent improvements in machine tool rigidity and the development of ceramic and CBN cutting tools allow the machining of hardened steel. Even though hard turning consists of
small depths of cut and feed rates, material removal rates can be much higher than those achieved by grinding, depending on the application. Estimates of reduced machining time are as high as
60%. This reduction can make it possible to employ flexible manufacturing systems and reduced batch sizes, both of which are growing more important in industry. Aside from decreases in machining
time, reducing the number of required machine tools may be a result of the increased flexibility of hard turning compared to grinding. Using fewer machines would reduce part-handling costs and
the cost associated with having multiple operators and machine setups. Hard turning can also be done without coolant.
Crater wear after 20 passes
It seems obvious that hard turning is an attractive replacement for many grinding operations, but implementation in industry remains relatively uncommon, particularly for critical surfaces.
Several issues remain unaddressed. For one, hard turning can influence the workpiece surface microstructure by generating undesirable residual stress patterns and overhardened surface zones,
known as white layers. The cause of these residual stress patterns and white layers and their effect on parts are not fully understood. Also, because cutting tools required for hard turning are
much more expensive than tools for conventional turning, tool life influences the economics when users seek to replace grinding operations with hard turning.
To become a realistic replacement for many grinding operations, hard turning must prove it can create equivalent finished surfaces. It must hold geometric tolerances and produce undamaged
surfaces that conform to surface roughness requirements. Under ideal conditions, part geometry and surface finish comparable to those generated by grinding can be hard-turned with extremely rigid
machine tools and new cutting insert materials. With less rigid machines and improper cutting conditions, however, tool wear is excessive and eliminates any cost savings. Worn cutting tools also
increase the amount of surface damage observed on hard-turned components.
Flank Wear
For most cutting conditions, flank wear initially proceeds rapidly, but then settles as the wear progresses.
White layer and residual tensile stresses might be expected to reduce fatigue life. But research comparing fatigue life of hard-turned and ground surfaces found the hard-turned surfaces have
increased life despite the existence of brittle white layers. Compressive stresses found on hard-turned surfaces also improve fatigue lives. Because the effects of white layer on the resulting
component life are not well understood, industry remains reluctant to produce critical surfaces by a hard turning process that may contain white layers. More research is needed to determine how
cutting parameters affect tool wear and surface integrity.
Flank wear after 40 passes
As this article is prepared, we've tested thirteen different cutting conditions. They span the range of recommended conditions for the cutting tools used, and match
reasonable conditions selected in past research and by industry. Cutting speed, feed rates, and radial depths of cut were varied for four different tool materials, made by two CBN insert
suppliers. We machined 52100 tube stock hardened to approximately RC62. This hardness was maintained throughout the thickness of the tube, as it was possible to quench from both the OD and ID.
The test conditions contained five subgroups. Divisions are based primarily on the cutting tool material, although the first two subgroups are separated by radial depth of cut. The second
grouping is the only set of tests run at the larger radial depth of cut.
Cutting tools for all experiments were CBN-tipped cutting inserts that, in combination with the toolholder, provided -5º side and back rake angles, a 0.794-mm nose radius, and a 20º edge chamfer
0.102-mm wide. Cutting forces were recorded during each test pass using a piezoelectric dynamometer. Tool inspections were made with a standard optical microscope and a scanning electron
microscope.
Tool wear not only reduces tool life, but also affects surface finish, increases cutting forces and tensile residual stress, and causes white layer surface damage.
Resistance to tool wear is a function of many variables, including CBN content, grain size, binder material, tool geometry, cutting edge geometry (sharp vs. chamfered), workpiece properties, and
cutting conditions. The brittle nature of ceramic and CBN tools makes them prone to chipping at the cutting edge, while abrasive wear and adhesion may cause premature tool failure.
Lower-CBN-content tools with a ceramic binder are generally more resistant to abrasive wear due to increased bonding strength, while higher-CBN-content tools with metallic binders have improved
fracture toughness. More work needs to be done to determine how tool material, workpiece material, tool geometry, and cutting conditions affect wear rates and life of CBN cutting tools.
Note that condition 5 is a replication of condition 1, but on the harder tube material. Conditions 3 and 4 are the only replication of identical machining conditions and same workpiece
material.
For all tested conditions, tool failure was declared when an edge fracture was noticed on the tool, or when the flank wear exceeded 200µm. We selected the 200µm condition because almost all tools
fractured with a flank land measurement between 150 and 200µm. Cutting time could be calculated as a measure of tool life, instead of the volume of material removed. Cutting time can be
calculated using the following relationship, where V is the volume of material removed in cm3, f is the feed in cm/rev, d is the radial
depth of cut in cm, s is the tangential cutting speed in cm/min, and t is the cutting time in minutes.
Tool life dramatically improvedat conditions when cutting speed was 91.4 m/min instead of 182.9 m/min. In general, increased feed reduced tool life. The effect of cutting speed
was more dominant than the effect of feed rate, so to improve tool life, slower cutting speeds should be selected in combination with increased feed rates. Because material removal rate is
linearly related to both feed rate and cutting speed, halving cutting speed while doubling feed rate maintains an equal removal rate. There are, however, limitations on acceptable feed
rates-determined by the ability of the cutting tool to withstand increased cutting loads without fracture.
Increasing radial cutting depths also could increase removal rates, although cutting depth is often determined by the amount of stock removal required. As in the case of increased feed rates,
tool life decreased with increased depth of cut. As expected, a tradeoff exists between tool life and removal rate. Optimal conditions must factor the cost benefit of decreased machining times
with increased tool wear and the associated cost of increased machine downtime.
High-CBN-content tools typically have 90% or more CBN bonded with a cobalt binder material, while the low-CBN-content tools may contain only 40-60% CBN with a mixture of ceramic binder materials.
The increased strength of the binder material in the low-CBN tools may explain the observed increase in tool life. Yet, low-CBN tools may not perform well for more aggressive cutting conditions
or interrupted cuts, where the higher fracture toughness of high-CBN-content tools would be beneficial.
In addition to the cost effects of tool life, changes to the cutting mechanics due to tool wear and associated changes in cutting geometry are important in hard turning. This observation is
particularly true because cutting tools are typically prepared with chamfered or honed edges, and the cutting geometry takes place primarily along these edges.
Because the chip-contact area occurs along the chamfered nose of the cutting tool, nominal cutting geometry can change significantly during the life of the cutting tool. To monitor changes in the
nominal geometry, we used a New View 200 microscope, made by Zygo Inc. (Middlefield, CT), to produce three-dimensional images of the cutting edge. For inserts with a 20º edge chamfer and a
toolholder with a negative 5º rake angle, the effective combined rake angle is 25º, assuming that cutting takes place primarily on the edge chamfer. Crater wear changes that geometry
significantly, which also impacts the cutting process. While crater wear is important because it changes nominal cutting geometry, flank wear is the more typical method of quantifying the
condition of a cutting tool.
Measurement of the flank land was possible using images from the Zygo microscope, an optical microscope, or SEM. With the Zygo data, two-dimensional profile sections can be obtained to easily
measure the maximum length of the flank land directly from the analysis software provided with the microscope. Plotting the flank land measurements against the volume of material removed with the
cutting tools shows a common pattern in the wear data.
Tool Life for All Cutting Conditions
This figure shows the tool life of each cutting condition listed in the table above, measured by the amount of material removed with the tool.
Results indicate most tools failed when flank wear was between 150 and 200µm. While the cause is ultimately a loading that causes brittle fracture on some portion of the cutting edge, knowing the
range of flank wear that corresponds to this condition may provide a simple way to predict failure. Knowing failure is expected beyond a flank land of 150µm provides a basis for calculating the
amount of material (or cutting time/cutting length) that can be safely machined with a tool at different cutting conditions. More work will help determine how cutting parameters influence
constants, so we can develop a method for predicting flank wear for ranges of reasonable cutting conditions.
If hard turning is to replace finish grinding operations, it must be capable of producing surface finishes comparable to those generated by grinding. Unlike grinding, where
surface finish is determined by the size, shape, hardness, and distribution of abrasive grains in the grinding wheel, hard-turned surfaces are nominally defined by the geometry of the cutting
process, primarily by the cutting tool's feed rate and nose radius.
From profile data, arithmetic centerline average roughness Ra can be calculated by Equation (1) below. For conditions typical in hard turning, it can be approximated by Equation (3),
where f is the feed/revolution and R is the nose radius of the cutting tool.
(1)
(3)
For most cutting conditions, experimental and theoretical Ra values match very well, except at low feed. The discrepancy at low feeds is explained by an increase in the dominance of plowing
action. This explanation is reasonable, because at lower feeds, cutting depth decreases across the entire length of the cutting edge. Ideally, feed could be used to determine the quality of a
finish-machined surface. This is not possible, however, due to increased plowing, which causes material to deform plastically around the nose of the cutting tool and produce larger peaks on the
machined surface than theoretical calculations predict. Larger nose-radius tools would help improve finish, but plowing will always limit surface quality.
Most research on surface integrity of hard-turned steel surfaces has concluded that hard turning results in a thin rehardened surface layer of material that may be followed
by an overtempered region just beneath the white layer. Due to the microstructural changes to the material, the rehardened layer looks white in an optical micrograph after chemical etching, while
the tempered region appears dark, thus the terms white-etching areas and dark-etching areas.
While most research has shown the existence of white layers on hard-turned surfaces, the cause, magnitude, and effect of such layers are not well-understood. White layers are typically associated
with residual tensile stress at the surface, while in some conditions white-layer surfaces exhibit residual compressive stresses. Obviously, residual stress on a surface affects the performance
of a workpiece in service. There are differing results, for example, on the fatigue lives of hard-turned surfaces compared to ground surfaces.
Cutting coolant can influence the generation of white layer. Because white layer is thought to occur as the result of a phase transformation on the surface (very similar to the bulk heat
treatment of steels), cutting coolant might help eliminate thermal damage by keeping the workpiece surface cool. Some reports say cutting coolant eliminates white layer, but other studies show
coolant having no effect. Tool condition is also believed to be an important factor, with new tools producing undamaged surfaces, while white layer increases with increasing tool wear. The cause
of this increase is not clearly defined, but may result from increased heat generated by friction between the tool and workpiece as the flank land increases. It may also result from increased
plastic deformation associated with increased friction.
Surface integrity in hard turning also causes some reluctance to use hard turning as a finishing operation for critical surfaces. Despite such reports, current research shows hard turning, even
with very worn cutting tools, can produce undamaged surfaces.
The proposed explanation for the existence of white layer when cutting with low-CBN-content tools and not with high-CBN-content tools is a difference in thermal conductivity, with the
high-content tool's conductivity being twice that of low-content tools. There are primarily three routes for heat removal from the cutting process: the chip, the tool, and the workpiece. Assuming
that most heat is removed with the chip, the remaining heat must go into the workpiece and cutting tool. If resistance to heat flow into the tool increases, the workpiece surface will get hotter,
a condition that low-CBN-content tools can produce.
Hard turning offers many potential benefits when compared to grinding. To increase the use of this technology, questions about its ability to produce surfaces that meet
surface finish and integrity requirements must be answered. In addition, the process must be justified economically, which requires a better understanding of tool wear patterns and life
predictions.
引用出處：
http://tw.myblog.yahoo.com/lifung-biz/article?mid=4381&prev=4382&next=4379
歡迎來到Bewise
Inc.的世界，首先恭喜您來到這接受新的資訊讓產業更有競爭力，我們是提供專業刀具製造商，應對客戶高品質的刀具需求，我們可以協助客戶滿足您對產業的不同要求，我們有能力達到非常卓越的客戶需求品質，這是現有相關技術無法比擬的，我們成功的滿足了各行各業的要求，包括：精密HSS
DIN切削刀具、協助客戶設計刀具流程、DIN or JIS
鎢鋼切削刀具設計、NAS986 NAS965 NAS897 NAS937orNAS907
航太切削刀具,NAS航太刀具設計、超高硬度的切削刀具、醫療配件刀具設計、複合式再研磨機、PCD地板專用企口鑽石組合刀具、粉末造粒成型機、主機版專用頂級電桿、PCD
V-Cut刀、捨棄式圓鋸片組、粉末成型機、航空機械鉸刀、主機版專用頂級電感、’汽車業刀具設計、電子產業鑽石刀具、木工產業鑽石刀具、銑刀與切斷複合再研磨機、銑刀與鑽頭複合再研磨機、銑刀與螺絲攻複合再研磨機等等。我們的產品涵蓋了從民生刀具到工業級的刀具設計；從微細刀具到大型刀具；從小型生產到大型量產；全自動整合；我們的技術可提供您連續生產的效能，我們整體的服務及卓越的技術，恭迎您親自體驗！！
BW Bewise Inc. Willy Chen willy@tool-tool.com bw@tool-tool.com www.tool-tool.com skype:willy_chen_bw mobile:0937-618-190 Head &Administration Office No.13,Shiang Shang 2nd
St., West Chiu Taichung,Taiwan 40356 http://www.tool-tool.com/ / FAX:+886 4 2471 4839
N.Branch 5F,No.460,Fu Shin North Rd.,Taipei,Taiwan S.Branch No.24,Sec.1,Chia Pu East Rd.,Taipao City,Chiayi Hsien,Taiwan
Welcome to BW tool world! We are an experienced tool maker specialized in cutting tools. We focus on what you need and endeavor to research the best
cutter to satisfy users’ demand. Our customers involve wide range of industries, like mold & die, aerospace, electronic, machinery, etc. We are professional
expert in cutting field. We would like to solve every problem from you. Please feel free to contact us, its our pleasure to serve for you. BW product including: cutting
tool、aerospace tool .HSS DIN Cutting tool、Carbide end
mills、Carbide cutting tool、NAS Cutting tool、NAS986 NAS965
NAS897 NAS937orNAS907 Cutting Tools,Carbide end
mill、disc milling cutter,Aerospace cutting tool、hss
drill’Фрезеры’Carbide drill、High speed steel、Compound
Sharpener’Milling cutter、INDUCTORS FOR PCD’CVDD(Chemical Vapor Deposition Diamond )’PCBN (Polycrystalline Cubic Boron
Nitride) ’Core drill、Tapered end mills、CVD Diamond Tools Inserts’PCD
Edge-Beveling Cutter(Golden Finger’PCD V-Cutter’PCD Wood tools’PCD Cutting
tools’PCD Circular Saw Blade’PVDD End Mills’diamond tool. INDUCTORS
FOR PCD . POWDER FORMING MACHINE ‘Single Crystal Diamond ‘Metric end mills、Miniature
end mills、Специальные режущие инструменты ‘Пустотелое сверло
‘Pilot reamer、Fraises’Fresas con mango’ PCD (Polycrystalline
diamond) ‘Frese’POWDER FORMING MACHINE’Electronics cutter、Step
drill、Metal cutting saw、Double margin drill、Gun
barrel、Angle milling cutter、Carbide burrs、Carbide tipped
cutter、Chamfering tool、IC card engraving cutter、Side cutter、Staple
Cutter’PCD diamond cutter specialized in grooving floors’V-Cut PCD Circular Diamond Tipped Saw Blade with Indexable Insert’ PCD Diamond
Tool’ Saw Blade with Indexable Insert’NAS tool、DIN or JIS
tool、Special tool、Metal slitting saws、Shell end mills、Side
and face milling cutters、Side chip clearance saws、Long end mills’end mill
grinder’drill grinder’sharpener、Stub roughing end
mills、Dovetail milling cutters、Carbide slot drills、Carbide torus
cutters、Angel carbide end mills、Carbide torus cutters、Carbide ball-nosed slot
drills、Mould cutter、Tool manufacturer.
Bewise Inc. www.tool-tool.com
ようこそＢｅｗｉｓｅ Ｉｎｃ.の世界へお越し下さいませ、先ず御目出度たいのは新たな
情報を受け取って頂き、もっと各産業に競争力プラス展開。
弊社は専門なエンド・ミルの製造メーカーで、客先に色んな分野のニーズ、
豊富なパリエーションを満足させ、特にハイテク品質要求にサポート致します。
弊社は各領域に供給できる内容は：
（１）精密ＨＳＳエンド・ミルのＲ＆Ｄ
（２）Carbide Cutting tools設計
（３）鎢鋼エンド・ミル設計
（４）航空エンド・ミル設計
（５）超高硬度エンド・ミル
（６）ダイヤモンド・エンド・ミル
（７）医療用品エンド・ミル設計
（８）自動車部品＆材料加工向けエンド・ミル設計
弊社の製品の供給調達機能は：
（１）生活産業～ハイテク工業までのエンド・ミル設計
（２）ミクロ・エンド・ミル～大型エンド・ミル供給
（３）小Ｌｏｔ生産～大量発注対応供給
（４）オートメーション整備調達
（５）スポット対応～流れ生産対応
弊社の全般供給体制及び技術自慢の総合専門製造メーカーに貴方のご体験を御待ちしております。
Bewise Inc. talaşlı imalat sanayinde en fazla kullanılan ve üç eksende (x,y,z) talaş kaldırabilen freze takımlarından olan Parmak Freze imalatçısıdır. Çok geniş ürün yelpazesine sahip
olan firmanın başlıca ürünlerini Karbür Parmak Frezeler, Kalıpçı Frezeleri, Kaba Talaş Frezeleri, Konik Alın Frezeler, Köşe Radyüs Frezeler, İki Ağızlı Kısa ve Uzun Küresel Frezeler, İç Bükey
Frezeler vb. şeklinde sıralayabiliriz.
BW специализируется в научных исследованиях и разработках, и снабжаем самым высокотехнологичным карбидовым материалом для поставки режущих / фрезеровочных инструментов
для почвы, воздушного пространства и электронной индустрии. В нашу основную продукцию входит твердый карбид / быстрорежущая сталь, а также двигатели, микроэлектрические дрели, IC картонорезальные
машины, фрезы для гравирования, режущие пилы, фрезеры-расширители, фрезеры-расширители с резцом, дрели, резаки форм для шлицевого вала / звездочки роликовой цепи, и специальные нано инструменты.
Пожалуйста, посетите сайт www.tool-tool.com для получения большей
информации.
BW is specialized in R&D and sourcing the most advanced carbide material with high-tech coating to supply cutting / milling tool for mould & die, aero space and
electronic industry. Our main products include solid carbide / HSS end mills, micro electronic drill, IC card cutter, engraving cutter, shell end mills, cutting saw, reamer, thread reamer,
leading drill, involute gear cutter for spur wheel, rack and worm milling cutter, thread milling cutter, form cutters for spline shaft/roller chain sprocket, and special tool, with nano grade.
Please visit our web www.tool-tool.com for more info.
